ITU digital signal level 1 (2.048 Mbps) = CEPT 1.

ITU digital signal level 3 (34.368 Mbps) = CEPT 3.

Energy to Interference ratio.

Energy to Noise ratio.

Error Correction Code.

Electrically Erasable Programmable Read Only Memory

Electronic Industries Association

Excess Information Rate

Extended Industry Standard Architecture - A 32-bit bus standard that supports the features of microchannel architecture. A special card is required for 32-bit operations that maintain compatibility with the older ISA (Industry Standard Architecture).

Though the electromagnetic spectrum was, by custom and practice, formerly divided into 26 alphabetically designated bands, the ITU formally recognizes 12 bands, from 30 Hz to 3000 GHz.

An Ethernet service type that is based on a multipoint-to-multipoint EVC.

Element Manager.

Electro-Magnetic Compatibility.

Electromagnetic interference.

Element Management Level in the TMN model.

Element Management System.

The time it takes a signal to travel from point of transmission, to the point of reception.

Engineering Orderwire (Voice and/or Data).

Effective Radiated Power.

Errored Second.

Extended SCAN Protocol. A Harris Stratex proprietary protocol that is more efficient and allows for faster communications than the SCAN protocol

Electrostatic discharge.

Errored Second Ratio.

The term Ethernet refers to the family of local-area network (LAN) products covered by the IEEE 802.3 standard that defines what is commonly known as the CSMA/CD protocol. Data rates are defined for:

Ethernet

10 Mbit/s - 10Base-T Ethernet

Ethernet

100 Mbit/s - Fast Ethernet

Ethernet

1000 Mbit/s - Gigabit Ethernet

Ethernet

10000 Mbit/s - 10-Gigabit Ethernet

ETSI

European Telecommunications Standards Institute. Provides international technical standards for wireless radios. Harris Stratex Networks radios are in compliance with all relevant ETSI standards.

EVC

Ethernet Virtual Connection. An association of two or more UNIs that limits the exchange of frames to UNIs in the Ethernet Virtual Connection.

The amount of attenuation a link can suffer before link performance is affected. Typically measured as the dB difference between the received signal strength and the receive threshold.

Fault, Configuration, Accounting, Performance and Security functions in the TMN model.

Federal Communications Commission. The FCC is an independent United States government agency, directly responsible to Congress. The FCC was established by the Communications Act of 1934 and is charged with regulating interstate and international communications by radio, television, wire, satellite and cable. The FCC's jurisdiction covers the 50 states, the District of Columbia, and U.S. possessions.

Frame Check Sequence.

Frequency Diversity. A path protection mode. The main and standby radios are transmitting simultaneously and are tuned to different frequencies (at least two channels apart) to avoid interference. When a fault is detected on the active radio, the traffic is switched to the standby radio.

Forward Error Correction. A system of error control for data transmission. It compensates for errors induced in the transmitted stream, by sending along with the primary data payload, additional information to correct for errors that occur in transmission.

Frame Error Ratio.

Feed Forward Equalizer.

First In First Out.

Finite Impulse Response filter. Designates one of two primary types of digital filters used in Digital Signal Processing (DSP) applications.

Frame Loss Ratio. This is the measure of lost frames between the ingress UNI and the egress UNI. Frame Loss Ratio is expressed as a percentage.

Fault Management.

Field Programmable Gate Array.

Short for "Ethernet Frame."

The time required to transmit a Service Frame from ingress UNI to egress UNI.

Frequency-shift Keying. The modulating signal shifts the output frequency between predetermined values.

An ITU-T recommendation on error performance parameters and objectives for primary-rate (64 kbit/s) data circuits. It can be used for higher bit-rates, typically up to to 2 Mbit/s. G.821 is a bit-based system.

An ITU-T recommendation on error performance parameters and objectives for high-speed data circuits; circuits operating at 2 Mbit/s and above. G-826 is a block-based system.

Gallium Arsenide Field Effect Transistor.

The increase in signal power caused by a device or network (for example, the signal gain provided by an antenna).

Generic Attribute Registration Protocol

Gigabyte.

Gigabit Ethernet.

Gigahertz.

These are sites where it is imperative that communications traffic continues at peak performance. They are typically sites where any communications down-time can mean significant loss of revenue, or a significant breach against a service level agreement (SLA).

General packet radio service (GPRS) is a packet oriented mobile data service available to users of the 2G cellular communication systems global system for mobile communications (GSM), as well as in the 3G systems. In the 2G systems, GPRS provides data rates of 56-114 kbit/s.

The Global Positioning System (GPS) is a global navigation satellite system (GNSS) developed by the United States Department of Defense and managed by the United States Air Force 50th Space Wing. It is the only fully functional GNSS in the world, can be used freely, and is often used by civilians for navigation purposes. It uses a constellation of between 24 and 32 Medium Earth Orbit satellites that transmit precise microwave signals, which allow GPS receivers to determine their current location, the time, and their velocity. Its official name is NAVSTAR GPS. Although NAVSTAR is not an acronym,[1] a few backronyms have been created for it.

Global Systems for Mobile.

Graphical User Interface.

A standard approved by the ITU that defines how audiovisual conferencing data is transmitted across networks. In theory, H.323 should enable users to participate in the same conference even though they are using different videoconferencing applications.

High Density Bipolar Order 3. The default method of encoding transmissions for E1 and E3 radios. Substitutes a 1 for every 3 zeros.

High-level Data Link Control. A bit-oriented synchronous data link layer protocol developed by ISO. HDLC specifies a data encapsulation method on synchronous serial links using frame characters and checksums.

Handheld terminal.

A protected system configuration whereby if a fault occurs at the receiving end of the link, the traffic is switched to the standby radio without causing errors.

Hot Standby is a protected configuration whereby standby equipment is held ready to be switched immediately into service if the main equipment fails.

High Power Amplifier.

Hot-Standby Protection Mode.

Hardware/Software Compatibility. Different hardware may require different software versions.

Input / Output.

Internet Control Message protocol. An integral part of the Internet Protocol that handles error and control messages.

Indoor Chassis.

Intermediate Frequency. The signal frequency or frequencies intermediate between the modem electronics and the transmitted/received frequencies.

CORBA's Internet Inter-ORB Protocol.

Indoor Unit. The IDU s the control center of a split-mount radio system. It interfaces between the customer signals and the ODU.

Institute of Electrical and Electronics Engineers.

Internet Engineering Task Force.

Interior Gateway Protocol.

Intermodulation can occur in systems where multiple signals are present at the same point. Where there is a nonlinearity in the system any signal will generate harmonics, but when two signals are present, harmonics of both are produced. The harmonics of the two signals can intermix, resulting in further spurious signals that are known as intermodulation products. The result of an intermodulation signal can have a major impact on reception if it falls in a receive channel. As the number of signals increases and/or TX power increases, the probability of an intermodulation signal causing noise in a receive channel grows.

International Telecommunications Union. A civil organization established to promote international standards for telecommunications.

Intelligent Node Unit. INU is the term used to describe the indoor unit of a Harris Stratex Networks Eclipse Node. The INU is a 1U chassis (the IDC) fitted with mandatory cards plus option cards. It supports up to three ODUs for three non-protected links, or one protected/diversity link and one non-protected link.

Expanded Intelligent Node Unit. The Harris Stratex Networks term used to describe the 2U indoor unit of an Eclipse Node. The INUe supports up to six ODUs for six non-protected links, or up to three protected/diversity links.

Internet Protocol. A method or protocol by which data is sent from one device to another on the Internet.

Indoor Radio Unit.

Inter-Symbol Interference.

International Standards Organization.

International Telecommunication Union - Radio Communication Sector (formerly CCIR and IFRB).

International Telecommunication Union - Telecommunication Standardization Sector (formerly CCITT).

K1 and K2

In an SDH system, K1 and K2 are MSOH bytes used for:

Controlling the multiplexer section protection switching.  Signalling Alarm Indication Signal (AIS), Far End Remote Failure (FERF). Signalling Automatic Protection Switching (APS) alarms, when implemented.

Layer 1.

Layer 2.

Link Aggregation Control Protocol.

Link Aggregation Group.

Local-area Network. A data network located on a user's premises within a limited geographical area. Ethernet is the most widely used LAN transport technology.

Line Build-Out (I/O Cable Distance Compensator).

Light Emitting Diode.

A radio link comprises two terminals, one at each end of the link.

Liquid bandwidth refers to the Eclipse ability to seamlessly assign capacity to Ethernet and to companion E1/DS1 or STM1/OC3 traffic. This scalability is enabled by the unique universal modem design built into Eclipse. It does not distinguish between the type of data to be transported, Ethernet or TDM; data is simply mapped into byte-wide frames to provide a particularly efficient and flexible wireless transport mechanism, with the result that when configured for Ethernet and/or TDM, the full configured capacity is available for user throughput.

Logical Link Control.

Low-medium capacity data radio.

Local Maintenance Terminal.

Low Noise Amplifier.

Local Oscillator.

Loss of Frame or Loss of Frame Alignment.

Line Overhead. Contains the media's framing, routing protocol, and network-layer protocol overhead.

A diagnostic function designed to assist testing of system components by routing traffic back to the direction it came from.

1) Loss of signal; 2) Line of Sight.

Label Switched Path.

Label Switched Router.

Line Termination Equipment.

Media Access Control.

Media Access Control address. A unique number assigned to every layer 2 Ethernet device in the world.

Management Information System.  An organized assembly of resources that collects, processes, and distributes data.

Megabits Per Second. Also Mbit/s.

A device or logic that implements a mapping function.

Metro Ethernet Forum.

Metro Ethernet Network.

Scratch pad text area that allows radio users to leave each other messages.

Master Ground Bar.

Monitored Hot Standby.

Megahertz = 1 million hertz.

Management Information Base. A file that describes the information that can be accessed for each network device. The MIB is required by SNMP.

Microwave Monolithic Integrated Circuit.

Management Information System. An organized assembly of resources that collects, processes, and distributes data.

MultiMediaCard. A compact, removable standard for storing and retrieving digital information in small, low-power devices. MultiMediaCards use flash technology for reusable recording, and ROM technology for read-only applications.

A device used to convert digital signals into analog signals suitable for transmission over analog communications channels and/or recover digital signals from analog signals.

Multi-Protocol Label Switching.

Multiplexer Section Overhead. Part of an SDH frame.

Multi Service Provisioning Platform

Multiplexer Switching Unit.

Mean Time Between Failure. The average time (usually expressed in years) over which a component operates without failure.

Mean Time Between Outages. A function of MTBF, MTTR and the probability that the monitoring circuits detect a failure. The only circuits considered in the MTBO calculations are the ones that impact traffic.

Mean Time to Restore.

Mean Time to Repair. The average time taken to repair or replace a failed device.

A multiplexer sends/receives two or more signals over the same channel.

When a transmitter is muted, it is prevented from transmitting.

Multiplexer. A device that combines two or more information-carrying channels for transmission over one channel, by using frequency division or time division techniques.

The process used to map Ethernet over a transport media whereby the Ethernet format and its structure are retained ?untouched? during transmission. This is distinct from the mechanism of encapsulation, where Ethernet frames are encapsulated within other formats such as E1/DS1, E3/DS3 or SDH/SONET frames.

North Bound Interface.

Network Element.

Network Elements Level in the TMN model.

Network Management Interface.

The organization responsible for installing and maintaining a radio network.

Network Management Level in the TMN model.

Network Management Centre.

Network Management System.

Network Operations Center.

A network device or device-grouping that is mid-point in a network, as distinct from a terminal device that is at the end/edge of a network.

A 1+0 configuration in which there is only one set of equipment.

Overhead and Maintenance.

The object class identifies the radio type to which the object belongs.

A group of network elements created using user-defined selection criteria.

Optical Carrier Level n. The optical signal that results from an optical conversion of a synchronous transport signal n (STS-n). This is the signal that will form the basis of the interface.

Outdoor Unit. ODU generally refers to the outdoor transceiver unit that is co-located with an antenna in a split-mount radio system.

Original Equipment Manufacturer

The unit of electrical resistance. A potential difference of one volt across a circuit resistance of 1 ohm produces a current of one ampere.

Optical Multimode

Optical Single Mode

An auxiliary communications channel provided for use by maintenance and service personnel, typically allowing both voice and/or data transmission between radio terminals.

An electronic circuit designed to produce an ideally stable alternating voltage or current.

Open Systems Interconnection

Open Shortest Path First. An OSI layer 3 dynamic routing protocol.

Operations Support System.

Power Amplifier.

Pulsed Amplitude Modulation.

A radio path refers to the path traversed by the signal between two radios.

Provider Backbone Transport.

Printed Circuit Assembly.

Printed Circuit Board.

Pulse-code Modulation. Modulation in which a signal is sampled, quantized and then digitized for transmission. PCM is the basic method of encoding an analog voice signal into digital form using8-bit samples.

Paperless Chart Recorder. A software based diagnostic tool that stores operational data from a remote radio and provides view capability to the user.

Personal Communications Service. A set of capabilities that provides a combination of terminal mobility, personal mobility, and service profile management.

Personal Digital Assistant

Plesiosynchronous Digital Hierarchy. A multiplexing scheme of bit stuffing and byte interleaving. It multiplexes the lower level 64 kbit/s circuits into a successively higher order 2 Mbit/s, 34 Mbit/s, 140 Mbit/s and 565 Mbit/s aggregate rates.

Protocol Data Unit.

A message used to determine whether an IP address is accessible on a network.

Plug-In Unit

Phase-locked Loop. A circuit that controls an oscillator so that it maintains a constant phase angle relative to a reference signal.

Party Line Telephone.

Performance Management.

Protection Multiplex Adaptor.

Part Number.

A part of the SDH/SONET overhead that locates a floating payload structure.

Parts per million.

Point-to-Point Protocol. A TCP/IP routing protocol that allows communications over serial communications lines without the use of other adapters, such as modems.

Pseudo-Random Binary Sequence.

Primary Reference Clock.

Programmable Read Only Memory.

A unit that controls protection switching in hot-standby, diversity or ring protected devices.

An entity that performs information preparation and exchange on behalf of a device it is representing.

Primary Reference Source

Public switched telephone network.

Power Supply Unit.

Provider VLAN.

Pseudo-Wire.

Quadrature Amplitude Modulation. A method of modulating digital signals using both amplitude and phase coding.

Quality of Service.

Quadrature Phase Shift Keying. A method of modulating digital signals using four phase states to code two digital bits per phase shift.

Radio Access Card.

Radio Frequency Interference.

Remote Access Server.

Reverse Channel Switching. A feature set that provides protection against potential far-end transmitter silent failure.

Remote Defect Indication - Line.

A location qualified in accordance with IEC Standard 60950-1 as providing an access that can only be gained by Skilled Persons or users who have been instructed about the reasons for the restriction applied to the location and about any precautions to be taken; and access achieved through the use of a Tool, lock and key, or other means of security, and is controlled by the authority responsible for the location.

Radio Frequency.

Radio Frame Complementary Overhead. Refers to data that is added to a data transmission unit.

Radio Frequency Unit.

The member of the radio installation team responsible for installing the antenna and cabling on the transmission tower.

Radio Interface Module

Routing Information Protocol. An OSI layer 3 dynamic routing protocol.

1) Return Material Authorization; 2) Radio Modem Adaptor

Rack Mounting Space.

A layer 3 network device that interconnects networks. It directs data between two or more networks using information held in the IP header to decide whether to foward a packet, and over which network interface to send a packet, for it to reach its destination.

A protocol used between routers to exchange routing information. OSPF and RIP are the two most common dynamic routing protocols.

Radio Processing Card.

Resilient Packet Ring.

Revertive Switching. A process that sends traffic back to the original working system after the system returns online.

Received Signal Level. The signal level at the receiver input (from the antenna). RSL is usually expressed in dBm.

Regenerator Section Overhead. Part of an SDH frame.

Received Signal Strength Indicator. The raw indicator of signal level at the receiver input (from the antenna). Usually expressed as a voltage, RSSI is usually converted to dBm and presented as an RSL.

Rapid Spanning Tree Protocol.

Rack Unit, 1 standard EIA rack unit (44.5 mm / 1.75 inch)

Receive.

Surface Acoustic Wave (filter).

Stand Alone Synchronisation Element

Space Diversity.

Synchronous Digital Hierarchy. An international standard for synchronous data transmission. SDH uses a multiplexing structure that enables direct access to individual 2 Mbit/s data streams from within the higher order aggregate line signals.

Synchronous Data Link Control. A bit-oriented, full-duplex serial protocol that has spawned numerous similar protocols, including HDLC and LAPB.

An organization providing ethernet service(s).

Severely Errored Seconds.

Severely Errored Second Ratio.

System International units.

Simple Network Management Protocol A networking management protocol used to monitor network-attached devices. SNMP allows messages (protocol data units) to be sent to various parts of a network. Upon receiving these messages, SNMP-compatible devices (agents) return data stored in their Management Information Bases.

A skilled person in the microwave radio installation and maintenance industry is considered to have the necessary knowledge and practical experience of electrical and radio engineering to competently and safely carry out their work. They must have a full understanding of the various hazards that can arise from working on and around radio installations and be competent to take responsibility for their safety and the safety of any other personnel under their immediate supervision.

Service Level Agreement. A contract between a subscriber and an (ethernet) service provider specifying the agreed upon service level commitments and related business agreements.

Serial-Line Internet Protocol.

Service Level Specification.

Services Management Adaptor.

Service Management Level in the TMN model.

Short Message Service.

Subnetwork Connection Protection. Designates path-switched SDH rings that employ redundant, fiber-optic transmission facilities. Organized in pairs, one fiber transmits in one direction while the backup fiber transmits in the other. If the primary ring fails, the backup takes over.

Signal-to-noise ratio.

Synchronous Optical Network. An ANSI standard for synchronous data transmission on optical media that is the equivalent of SDH, described above.

A protection mode. The main and standby radios are set up in Hot Standby mode, but are connected to their own antennas. Both antennas, separated by a specific distance, are receiving the signal transmitted from the online radio at the other end of the link. If a fault occurs in the receiving end of the link, the traffic is switched to the standby radio without causing errors (hitless receive switching). As in Hot Standby mode, a fault detected in the online transmitter causes that transmitter to mute and the standby transmitter to unmute.

Software-Software Compatibility.

Secure Sockets Layer.

Synchronisation Supply Unit

Static routing requires manual configuration of the routing table within Layer 3 routers. Data is forwarded within a network via a fixed path defined by the static routes - it cannot adjust to changing line conditions, unlike dynamic routing.

Statistical Time Division Multiplexing. Time slots are assigned to signals dynamically to make better use of bandwidth.

ITU digital signal level used in Synchronous Digital Hierarchy (SDH) equivalent to a 51.84 Mbps data rate.

ITU digital signal level used in Synchronous Digital Hierarchy (SDH) equivalent to a 155.52 Mbps data rate.

Synchronous Transport Module-level N (Nx155.52 Mbps) where N = 1, 4, 16 or 64.

Spanning Tree Protocol.

Synchronous Transport Signal-level N (Nx51.84 Mbps) where N = 1, 3, 12, 48, or 192.

A portion of a network sharing a particular subnet address.

A 32-bit combination used to describe which portion of an address refers to the subnet and which part refers to the host.

Switch Unit.

Standing Wave Ratio.

The difference in MHz between transmit and receive frequencies for duplex radios.

A digital carrier system for DS1 signals. T1 is a term for a digital facility used to transmit a DS1 formatted digital signal at 1.544 megabits per second. The 'T' is about the carrier facility and the 'DS' is about the signal format, which includes the muxed relationship between DS0, DS1, DS2, and DS3.

T3 is a term for a digital facility used to transmit a DS3 formatted digital signal at 44.7 megabits per second. The 'T' is about the carrier facility and the 'DS' is about the signal format, which includes the muxed relationship between DS0, DS1, DS2, and DS3.

Transversal Adaptive Equalization.

Transmission Control Protocol/Internet Protocol. Protocols that define connectivity across computer platforms interconnected via the Internet. The TCP protocol is responsible for an error free connection between two computers, while the IP protocol is responsible for the data packets sent over the network.

Trellis-Coded Modulation. A bandwidth-efficient scheme that combines error-correction coding with modulation. The redundancy thus introduced by the coding does not expand the bandwidth, since the parity bits are absorbed by the extended signal constellation. Two-dimensional (2D) TCM uses dependency between in-phase and quadrature symbols, while four-dimensional (4D) TCM introduces dependency between symbols of two successive intervals.

Temperature Controlled Crystal Oscillator.

Time Division Multiplexing. Examples of TDM services include Nx64 k/bits, DS1, DS3, E1, E3, OC3, STM1, OC12, and STM3.

A terminal emulation program for TCP/IP networks such as the Internet. The Telnet program runs on your computer and connects your PC to a server on the network. You can then enter commands through the Telnet program and they will be executed as if you were entering them directly on the server console. This enables you to control the server and communicate with other servers on the network. To start a Telnet session, you must log in to a server by entering a valid username and password. Telnet is a common way to remotely control Web servers.

Trivial File Transfer Protocol.

Tributary Interface Module.

Telecommunications Management Network.

A database stored in non volatile memory.

A program interrupt, usually caused by some exceptional situation in the user program. In most cases, the operation system performs some action, then returns control to the program. Used for event notification with SNMP.

Transistor-Transistor Logic. It is often applied to a network where the core of the network is the trunk, and the various end-user connections are the leaves.

Tributary.

A common semiconductor technology for building discrete digital logic integrated circuits. It originated from Texas Instruments in 1965.

Transmit.

Universal Datagram Protocol/Internet Protocol. Used primarily for short, broadcast messages, such as for SNMP messaging. UDP does not guarantee reliability or ordering in the way that TCP does. Datagrams may arrive out of order, appear duplicated, or go missing without notice. Avoiding the overhead of checking whether every packet actually arrived makes UDP faster and more efficient than TCP, at least for applications that do not need guaranteed delivery. Time-sensitive applications often use UDP because dropped packets are preferable to delayed packets.

The UNI is the physical interface or port that is the demarcation between the customer and the service provider.

Coordinated Universal Time. A time format used when a time zone independent time and date is required. Identical to Greenwich mean time (GMT) for most purposes.

Serial data communication interface. Also called RS-232.

Virtual Container.

Voltage Controller Oscillator. An electronic circuit designed to produce an ideally stable alternating voltage.

Volts, direct current.

Video Display Emissions.

Voice Frequency signal.

Video graphics array. A display standard for IBM PCs.

Viterbi is “convolutional code” which is used in data correction circuits. It operates on serial data, one or a few bits at a time, unlike block codes such as Reed-Solomon, which operate on relatively large message blocks (typically greater than 100 bytes).

Virtual Local Area Network.

VLAN Identifier

Very Large Scale Integration.

Voltage Controlled Oscillator.An electronic circuit designed to produce an ideally stable alternating voltage.

Virtual Private LAN Service.

Virtual Private Network.

Voltage Standing Wave Ratio.

A port on the IDU for making a connection to the NMI card.

Wide-area Network. A network that provides telecommunication services to a geographic area larger than that served by a local area network or a metropolitan area network.

Wireless Application Protocol.

Web-based Maintenance Terminal.

The designation for a specific size of waveguide used to transmit the microwave RF signal.

Cross-Polar Discrimination.

Cross Polarized Interference Cancellation

Two transceivers are used at each end of a link to protect against transmission failure. If a data transmission fails on the operating transceiver, it is transferred to the backup transceiver. With a 1+1 protected microwave radio link, the protection mechanism normally allows receiver switching independently of the transmitter, and vice-versa.

Standard Electronic Industries Association size for a single rack unit (44.5 mm / 1.75 in.)